How to join vinyl flooring

how to join vinyl flooring

Install the first section of vinyl, taking care to spread the adhesive completely on the outside edges. Step 2 Roll out the second piece of vinyl, matching any pattern with the pattern of the first piece to ensure the integrity of the pattern. Step 3. Method 1: No Transition. Instead of using a transition piece where the two floors meet, pull the carpet tight and wrap the edge underneath. This will hide the unattractive cut edge of the carpeting. You can use staples or whatever method your professional installer recommends to hold the carpet down. Slide the edge of your vinyl floors underneath the curved edge of the carpeting to create a seamless .

Instead of using a transition piece where the two floors meet, pull the carpet tight and wrap the edge underneath. This will hide the unattractive cut edge of the carpeting.

You can use staples or whatever method your professional installer recommends to hold tp carpet down. Slide the edge of your how to overcome nervousness in public speaking floors underneath the curved edge of the carpeting to create a seamless transition.

Sand the bottom of the t-molding track and lay down a strip of glue at the edge of the carpet. Place the track so that the edge of it slides underneath the tack strip at the edge of your carpeting. You want the edge of the carpeting to go over the edge of the track. Install your vinyl floors up to the other edge of the track and snap in the t-molding, hiding the edge of both the carpet and the vinyl. You can also you a SlimTrim transition piece for this method.

Sand the base of the end cap, lay a strip of glue, and press the end cap in place. Wait for the glue to dry, then tuck in the edge of the floorimg and trim off any stray fibers with a utility knife.

Back to home. Floor Basics. Floor Safety. Placing an Order. Iona Mineral Core Tile Collection. How do I transition between vinyl flooring and carpet?

Apr 22,  · loveescorten.com video shows you how to seam vinyl flooring using Armstrong's S Seam Adhesive. The S Seam Adhesive works gr.

Last Updated: January 20, References. To create this article, 13 people, some anonymous, worked to edit and improve it over time. There are 7 references cited in this article, which can be found at the bottom of the page. This article has been viewed , times. Learn more Vinyl flooring is a great way to change the appearance of a room without spending too much money.

The application is fairly simple and easy for beginners too, making it a great option for someone without a lot of home-improvement experience. If you're trying to learn how to install your own vinyl flooring, read on in Step One for help. To install vinyl flooring, start by removing all furniture from the room and taking off baseboards or trim along the bottom of the wall.

After removing any old flooring, lay down a plywood underlayer on the ground and use a stapler to secure the plywood sheets along the edges. Wait a few minutes for bubbles in the adhesive to settle, then place the vinyl tiles in your desired pattern.

Finally, use a floor roller to push down the tiles so they will stick to the adhesive before letting it dry. For tips on how to install self-stick vinyl tiles, read on! Did this summary help you? Yes No. Log in Social login does not work in incognito and private browsers. Please log in with your username or email to continue. No account yet? Create an account. Edit this Article.

We use cookies to make wikiHow great. By using our site, you agree to our cookie policy. Cookie Settings. Learn why people trust wikiHow. Download Article Explore this Article parts. Tips and Warnings. Things You'll Need. Related Articles.

Article Summary. Part 1 of Measure and order your vinyl. Use a measuring tape to carefully determine the size of your room. It is imperative that you get accurate measurements, or else you may end up with too little vinyl to finish the job. Remove anything that will be in the way. Vinyl flooring can be placed in a variety of rooms, so the things you have to remove will vary depending on where you are placing your vinyl.

Take out any free-standing furniture, and then move on to appliances. Take out the old flooring. This step is primarily necessary if you have carpet that you are replacing with vinyl; vinyl flooring can cover nearly any floor surface, so long as it is rigid, flat, smooth, and dry. Pull up the old floor, and remove the threshold strips that trim out the doorways.

The next step, although tedious, is very important: work along the subfloor, pulling out or hammering in any and staples and nails that you encounter that are not driven below the floor surface.

Old flooring and floor adhesives may contain asbestos, so call your county for an asbestos test before pulling it or disturbing it. If your county building or environmental office doesn't offer this service, consult a private testing laboratory to find out how to gather samples and have them test them. Make a paper template of the floor. Cut heavy construction paper into large strips, and lay it across your floor.

Cut out any corners or built-in obstacles, and add measurements. Do this with multiple pieces of paper, until you've covered your entire floor. Then, tape all the pieces of paper together to form a full sized copy of the floor. Prepare your underlayer underlayment. For subfloors that require a lot of work to smooth, flatten, or level, installing an underlayment is the easiest way to make this correction.

Tape your paper template of the floor to your underlayer plywood. Use this as a guide, and cut the plywood to fit the flooring in your room. Carefully cut your plywood in sections that match up, checking for fit with each completed piece. Rough-cut the underlayer first, and then make more detailed cuts after fitting each piece. Place your underlayer.

Put your underlayer plywood sheets in the room, and leave them for 2 or 3 days. Install the underlayer. You should never use nails or screws in the underlayer, as these will cause bumps in the vinyl flooring. Work your way across the room, stapling the underlayer to the floor. Finish smoothing the underlayer. Work your way across the floor with a sander, smoothing down any edges that are not flush where they meet, or bumps in the underlayer.

Then, use a leveling compound to fill in these spaces and any cracks in the underlayer. This will help to provide a smooth underlayer, which is vital to having a smooth final application of your vinyl.

Follow the package directions for applying the floor leveling compound and make sure it is compatible with both the underlayer and the vinyl adhesive you will be using. Part 2 of Decide on the pattern for your vinyl. Vinyl typically comes in 12 inch square tiles, but it may come in sheets.

If you have vinyl sheets, all you have to do is cut it out to fit the room, allowing for seams if the room is wider than the sheet. Vinyl tiles, on the other hand, must be applied in a pattern. Determine how you will lay the floor. You may strike a chalk line as a guide to the first row of vinyl if you are using tiles. Keep in mind that you will always start your pattern in the center of the room and work your way out, in order to keep it symmetrical.

Determine the application process for your vinyl. There are two types of vinyl: self-stick, and glue down. Self-stick vinyl is very straight forward, as it comes with an adhesive backing that you use to stick it to the floor. Glue down vinyl takes a bit more work, as it requires you to put a layer of vinyl flooring glue on the underlayer prior to placing your vinyl. If you have self-stick vinyl, simply follow the directions for application and you are set. If you have unglued vinyl, continue on for instructions on applying it.

Mark your pattern on your paper template. To make applying your vinyl easier, you can lay it out and cut it to fit using your paper template. Simply lay the vinyl out on the template, and use it as a pattern for cutting your vinyl to size. Begin gluing the vinyl flooring. Get your vinyl flooring adhesive out, and get a notched trowel.

Start in a corner of the room following your pattern , and scoop out some of the glue onto the trowel. Always have a damp rag at the ready for spills or smears on the vinyl.

Lay the vinyl. For solid vinyl tiles VCT, or vinyl composition tiles , place each one flat, perfectly aligned with the row, and snugly abutting the previous tile. Do not slide the tiles when laying them, as this will "drag" the adhesive.

Press the vinyl down to stick it to the adhesive. Apply pressure as you roll over the tile in order to stick it to the adhesive and the underlayer. Continue applying the vinyl. Work your way across the floor, applying the vinyl according your your pattern. Lay out some of the glue, allow it to dry until tacky, stick the vinyl, roll over it with your roller, and repeat the process at the next section.

Fill the entire floor with the vinyl, until you reach the edges. If you need to cut vinyl to fit the odd edge spaces, do so now. Otherwise, place your cut vinyl into these spaces and roll over them to verify that they are secured. Finish the flooring. If you installed your vinyl flooring in a bathroom, use a caulk gun to caulk around the edges of the floor where they meet with the baseboards.

This will protect from water damage and help your vinyl to last longer. Get matching vinyl transition pieces that fit flat against the flooring and the carpeting.

4 thoughts on“How to join vinyl flooring

Add a comment

Your email will not be published. Required fields are marked*